How to Replace a Bath Tub Yourself: Removing as well as Replacing.
How to Replace a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
We've unearthed this post pertaining to How to Install a Bathtub down the page on the web and believe it made perfect sense to relate it with you on this site.
Installing a bath tub isn't precisely brain surgery, but it does call for strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently obtainable, the project can relocate easily; if you have to open up a wall surface to eliminate the old tub and position the brand-new tub, the task is much harder. In either situation, the job is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Make certain you have qualified on your own for the task and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is better to take into consideration using one before you start. Possibilities are you might need a specialist plumber to make tube links.
This write-up will certainly aid you install a brand-new bath tub in your shower room if you have actually currently bought a brand-new bathtub and do not require to alter the plan of your previous supply of water pipelines.
Your devices and also product checklist should make up the following:
Planning for the Installation
Firstly, the sustaining framework supplied with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather problematic due to the restricted gain access to that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been gotten rid of, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
Prior to carrying on to fit the new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Using both wooden boards under its feet, place the bath tub in the called for placement. The wood boards are handy in uniformly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bathtub till the spirit level reads level.
To set up taps, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leaks and tighten them if essential. Fill up the tub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's user's manual. Tiling as well as securing around the bathtub must wait until the bath tub has been made use of a minimum of when as this will resolve it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making sure that the washing machines remain in area between the faucet and the sink. Safeguard the tap in place with the supplier provided backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap ports. The former type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a rigid seal, causing the water to pass through the wall surface in between the bathroom and the tiling, resulting in difficulties with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes as well as cartridges, and can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can crack relatively early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very intrigued by A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed the new page. Make sure you take the opportunity to promote this page if you enjoyed it. Thanks a lot for taking the time to read it.
Quote & Schedule Report this page